![]() How much does it cost to replace the Jeep 3.6 coolant temperature sensor? Then, attach everything back by following the reverse procedure. Remove and replace it with a new one by following the above guide. Step 3: You can now access the ECT sensor after removing the clip. To disconnect the clip, push that red clip out, then press down on the tab. Near the steering column, you’ll get a little red plastic clip. Then, look through the gap created after removing the braided cable. For this, look down on the engine compartment, and you’ll notice a braided cable and remove it. Step 2: Then, go to the driver’s side of your vehicle and stop at the front wheel to remove the electrical connector. ![]() Open your Jeep vehicle hood and remove the plastic cover from above the engine. Step 1: Disconnect the battery’s negative terminal. If you don’t get any available option to remove the inner fender liner to replace the ECT sensor, then follow the below step to know how you can access the sensor from above and replace it: Then, follow the reverse procedure to reinstall the inner fender line and the front wheel. Then, connect the connector by a snap, and remember to push the red tab to lock it in the actual position. You need to use a 19mm wrench to put back the new sensor on the cylinder head. Step 5: Installing is much easier than removing. Instead, use Loctite 567 or something similar. But don’t use Teflon tape if the sensor doesn’t come with sealant. Then, take the new sensor, and it should have sealant. You should do the replacement process rapidly to reduce coolant loss. When you do this process, you should keep ready the new one as there is coolant in the block. Step 4: Use a 19mm wrench to remove the engine coolant temp sensor. First, lift the red tab up and then push down the connector tab. You’ll notice a red plastic connector if you look through the inside compartment.Īfter removing the clip, you can access the actual sensor. Step 3: After removing the liner, you will have plenty of room to reach the coolant sensor. You can use a screwdriver to push the plastic push pins, which will come apart from the inside fender. Step 2: Then, you can access the inner fender panel, which is connected to the structure using a bolt and some pushpins. Then, remove the driver’s side front wheel. Then, lift up the vehicle’s driver-side portion using a jack stand. Step 1: To begin, disconnect the negative battery wires and drain the cooling system partially. So, if you want to save some money on labor costs and replace the ECT sensor, here is a complete guide on how you can do it in your Jeep 3.6L. The replacement cost will be high if you hire a professional to do the work. Replace the engine coolant temp sensor on Jeep 3.6L Also, you can access the sensor by removing the inner fender splash shield. You can visually inspect the sensor from above, but you need to remove a few engine parts to access it. The engine coolant temperature sensor is located in a water jacket at the rear of the cylinder head on the left side of the Jeep 3.6L engine. Noticeable black smoke from the tailpipe.Here are some other symptoms you might witness when the coolant temp sensor fails to work: After inspection by an obd2 scanner tool, if you get the P0128 error code, it means the thermostat is stuck open or the ECT sensor is damaged, and you should replace it. If you notice a check engine light appearing, it means your car is facing an issue, and you should inspect it. When to replace the coolant temperature sensor on Jeep 3.6? Don’t worry here is a complete walkthrough guide to locating the coolant temp sensor on your Jeep 3.6L and the replacement method. So, you need to replace your Jeep 3.6 coolant temp sensor when you detect any fault.īut, due to the high labor cost of replacing the temp sensor, many auto repair shops don’t want to disclose the exact location of the coolant temp sensor. If it fails to operate properly, it’ll cause unbalanced timing and fuel calculation. The coolant temp sensor reads the temperature of the coolant circulating through the engine.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |